Craftsman 5hp shredder blade removal how to#
Craftsman 5hp shredder blade removal manual#

STORAGE Prepare your chipper-shredder for storage at the end of the season or if the unit will not be used for 30 days or more. Never run your engine without air cleaner comВ pletely assembled. Cleaning with a forceful spray of water is not recommended as water could contamiВ nate the fuel system. Remove dirt and debris with a cloth or brush. Check Engine Oil Change Engine Oil Ill z V V Service Air CleanerДЄIR CLEANER CLEAN ENGINE The air cleaner prevents damaging dirt, dust, etc., from entering the carburetor and being force id into the engine and is important to engine life and perВ formance.

Push primer two or three times prior to starter operВ ation.Д¬USTOMER RESPONSIBILITIES MAINTENANCE SCHEDULE FILL IN DATES AS YOU COMPLETE REGULAR SERVICE SERVICE DATES H u Oil Pivot Points V o cc Clean Shredder V D a a.

Place the throttle control lever in FAST position (UP).

Refer to вЂњRemoving the Flail ScreenвЂќ in SERVICE AND ADJUSTMENT section.

If the unit runs out of gas as it is shredding or chipping, it may be necessary to unclog the unit befons it can be restarted.

Attach spark plug wire and rubber boot to spark of gasoline while operating the chipper-shredder.

Select the oilвЂ™s viscosity grade according to your expected operating temperature.Д¬heck the fuel level periodically to avoid l unning out GAS AND OIL FILL-UP OIL (Packed with Unit) Only use high quality detergent oil rated with API service classification SF, SG or SH. Pull up on the release bar, and lower the hopper assembly to the ground.

To lower the hopper assembly, use one hand to grasp the handle at the top of the hopper assembly and lift slightly.

Craftsman 5hp shredder blade removal how to#

HOW TO USE YOUR CHIPPER-SHF EDDER Do not attempt to shred or chip any matsrial other than vegetation found in a normal yard (i.e., branches, leaves, twigs, etc.). Disconnect spark plug wire and move away from spark plug to prevent accidental starting while equipment is unattended.Move throttle control lever to STOP position.No Larger Than 1/2' Diameter (Recommended) Or 1' Diameter (Maximum) TO STOP ENGINE

Craftsman 5hp shredder blade removal manual#

OPERATION KNOW YOUR CHIPPERвЂ™SHREDDER READ THIS OWNERвЂ™S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR CHIPPER-SHREDDER. Release plunger to lock it into position. Depress the plunger on the drawВ string, and pull on the drawstring until the bag is tight around the chute opening. To attach the bag, place the opening of the bag over the chute deflector so it completely covers the chute opening.N Upper Guide /ssembly Hex Bolt 8-3/8' Long Flat Washer Hex Lock Nut Inlet Guide FIGURE 3.Housing Asserlbly Spacers (Inside (Hinge) Hex Bolt Chute I )eflector HOW TO SET-UP YOUR CHIPPER-SHREDDER A MAKE CERTAIN THE SPARK PLUG WIRE IS DISCONNECTED AND MOVED AWAY FROM THE SPARK PLUG BEFORE ASSEMBLING THE CHIPPERSHREDDER. NOTE: To determine right and ieft hand sides of your chipper-shredder, stand behind the unit with the engine the farthest away from you. After assembly, see operaВ tion section of this manuai for proper fuel and engine oil recommendations. Hex Lock Nut 5/16-18 Thread LINE or OIL in the engine. ДЄSSEMBLY INSTRUCTIONS q: p IMPORTANT: This unit is shipped WITHOUT GASOВ eTYn^ Flat Washer 5/16' I.D. We have competent, welltrained technicians and the proper tools to service or repair this unit. Should you experience any problem you cannot easily remedy, please contact your nearest Sears Service Center/ Department in the United States. It has been designed, engiВ neered and manufactured to give you the best possible dependability and performance. Read this ownerвЂ™s manual carefully in its ertirety before vibration, immediately stop the engine, disconnect the attempting to assemble or operate this mach ne.Д¬ONGRATULATIONS on your purchase of a Sears Craftsman Chipper-Shredder.If the cutting mechanism strikes any foreign object or if TRAINING your machine should start making an unusual noise or FAIl URE TO COMPLY WITH THE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. SAFETY RULES A WARNING: TO REDUCE THE F OTENTIAL FOR ANY INJURY, COMPLY WITH THE FOLLOWING SAFETY INSTRUCTIONS. 247.795850 CRAFTSMAN Caution: Read and Follow All Safety Rules and Instructions Before Operating This Equipment 5 HORSEPOWER 3 CUTTING STAGE MULCHING AND BAGGING CHIPPER-SHREDDER Assembly Operation Customer Responsibilities Service and Adjustment Repair Parts SEARS, ROEBUCK AND CO., Hoffman Estates, IL 60179 U.S.A.